Replacement of spare tires is certainly not a simple job for beginners, and for many old drivers, they are unlikely to meet either! Sometimes on the road, if there is a tire problem and there is no repair shop nearby, Ben taught us the correct way to change tires today!

　　準備過程

　　Preparation process

　　首要你要準備幾樣?xùn)|西，備胎、三角牌、螺絲扳手、千斤頂!

　　First of all, you have to prepare several things, spare tires, triangle cards, screw wrenches, jacks!

　　三角牌的作用就不用說了，在換備胎時，放置在車后 50-100 米，高速上要 150 米，確保。剩下的就都是換胎用的東西了!注意，車要停好!盡或許排除隱患!

　　The role of the triangle is needless to say, in the replacement of spare tires, placed in the rear of the car 50-100 meters, 150 meters on the high-speed, to ensure safety. All that's left is for tire replacement! Pay attention, the car should stop well! Perhaps eliminate the potential safety hazards! uuuuuuuuuu

　　拆卸破損輪胎

　　Remove damaged tyres

　　別一上來就把千斤頂先弄上，必定先要用螺絲扳手送送螺絲(是擰松，不是卸下!)，注意，在松螺絲的時候，要采取對角線逐個擰松的辦法，由于這樣才不會使得螺絲、輪胎、輪轂變型!

　　Don't put the jack on first, you must send the screw with the screw wrench (it's loosening, not unloading!). Note that when loosening the screw, we should take the diagonal loosening method one by one, because this will not make the screw, tire, hub variant!

　　注：一般來說，逆時針是擰松螺絲，順時針是擰緊!螺絲一般比較緊，稍加用力才干松開，切記!

　　Note: Generally speaking, counterclockwise is to loosen the screw, clockwise is to tighten! The screw is generally tighter, slightly more effort to loosen, remember!

　　下一步就要使用千斤頂了!千斤頂都是有支撐方位的，一般在車輛中部下方，車輛都會有標示!一般間隔輪胎 10-15 分!如下圖所示!

　　The next step is to use the jack! The jacks are all bearing, usually in the middle of the car below, the vehicle will be marked! Tyre interval is generally 10-15! As shown in the following figure!

　　升起車身時，速度不宜過快，防止出現滑落等情況!車身不宜升起過高，能拆卸輪胎即可，過高了反而會給裝置等造成欠好的影響!

　　When lifting the body, the speed should not be too fast to prevent sliding and other situations! The body should not be raised too high, can dismantle the tires, too high will cause bad effects on the device, etc.

　　裝置備胎

　　Spare parts

　　裝置備胎時，困難的一步就是如何將備胎與螺絲孔對齊、固定!告訴我們一個好辦法，用手或者腳抵住輪胎，或許會好一點!別的，不要一上來就把螺絲全部擰死，必定等全部承認沒有問題，終在緊螺絲!

　　When installing spare tires, the most difficult step is how to align and fix spare tires with screw holes! Tell us a good way to put your hands or feet against the tires, maybe better! Otherwise, don't screw all the screw up, it must be acknowledged that there is no problem, and finally tighten the screw!

　　備胎只能解當務之急，不能長期使用，必定要先開到修理廠，將輪胎弄好!否則會有后患!行駛過程中，輪胎是非常重要的一環，我們需謹慎啊!

　　The spare tire can only solve the urgent matter, and can not be used for a long time. We must go to the repair shop first to get the tire well. Otherwise, there will be aftermath. In the course of driving, the tire is a very important part, and we need to be careful!