剎車燈是汽車尾燈中重要的信號指示器。它是一種非常重要的驅動設備。剎車燈是踩剎車時直接傳遞信號的指示器,主要起到警示汽車后方當前剎車的作用,能有效防止追尾事故的發生。一旦剎車燈不工作或出現故障,都會給我們帶來很大的隱患,我們一起來解決剎車燈不工作的問題。
Brake lamp is the most important signal indicator in automobile taillights. It is a very important driving device. Brake lamp is a direct signal indicator when braking. It can warn the current braking behind the car and effectively prevent rear-end collision. Once the brake lamp does not work or breaks down, it will bring us great hidden dangers. We will solve the problem of the brake lamp does not work together.
剎車燈不亮的原因:
The reason why the brake lamp is not on:
剎車燈不具備下列原因造成剎車開關、剎車燈線、剎車燈燈泡、剎車線保險失效。
Brake lamp does not have the following reasons which cause the failure of brake switch, brake lamp line, brake lamp bulb and brake line insurance.
解決方案:
Solution:
檢查剎車燈不亮,簡單的方法來制動剎車開關兩個電線電氣(剎車燈開關位置)腳踩剎車,如果沒有電解釋是剎車保險壞了,如果有一塊電,說明停車制動開關壞了,如果有電,所以檢查線和燈泡(通常是燈泡燒掉)。
Check the brake light is not on, a simple way to brake the brake switch two wires electric (brake light switch position) foot brake, if there is no electrical explanation is that the brake insurance is broken, if there is a piece of electricity, it means that the brake switch is broken, if there is electricity, so check the line and the bulb (usually the bulb burned).
這輛車的剎車燈壞了
The car's brake lights are broken.
這里有個提示,其實你可以檢查一下高剎車燈是否亮了,確定剎車燈是否亮了,有沒有電檢查開關還是的。
Here's a hint. In fact, you can check whether the high brake lamp is on, determine whether the brake lamp is on, whether there is an electric check switch or not, or whether it's safe.
剎車燈一直亮著
The brake lights were on all the time.
剎車燈的開關大多已出現剎車燈開關故障,或者由于電路短路,所以一般要檢查剎車燈開關和剎車線
Most of the switch of brake lamp has broken down, or because of short circuit, it is necessary to check the brake lamp switch and brake wire.
剎車燈有時關,有時開
Brake lights sometimes turn off and sometimes turn on.
當你踩剎車時,剎車燈有時不亮,有時亮。此故障主要是由于導線接觸不良,使剎車燈無法正常指示。
When you step on the brake, the brake lights sometimes don't turn on, sometimes they turn on. This fault is mainly due to poor wire contact, so that the brake lamp can not be normal instructions.
剎車燈忽亮忽滅
Brake lights flicker on and off
剎車燈一對一不上這種故障經常遇到,注意剎車燈泡是原因,更換剎車燈泡就可以解決
Brake lamp one-to-one failure is often encountered, pay attention to the reason of the brake lamp bulb, replacement of the brake lamp bulb can solve the problem.
注:更換剎車燈泡要同時更換兩個,是為了防止燈絲燒蝕程度可能不同,造成一個亮一個不亮的現象。但是車主可以在車上放一個好的燈泡,以備不時之需。
Note: Two brake bulbs should be replaced at the same time in order to prevent the filament from being ablated to different degrees, resulting in a phenomenon of not turning on. But the car owner can put a good light bulb in the car for a rainy day.
如果剎車燈壞了怎么辦?
What if the brake light breaks down?
話雖如此,如果路上剎車燈壞了怎么辦?剎車燈其實并不亮,車主可以完全解決自己的問題,如果有備用燈泡,只需打開后備箱擰下幾顆內螺絲,把雪橇上的燈泡蓋取下,把壞掉的燈泡直接拿下來就可以更換了。
Nevertheless, what if the brake lamp on the road is broken? The brake lamp is not on, so the owner can completely solve his problem. If there is a spare lamp, just turn on the backup box and screw down several internal screws, remove the bulb cover on the sled and replace the broken lamp directly.
如果沒有備用燈泡,車主必須小心減速,一方面,打開危險報警燈,另一方面,在右邊減速,尋找近的修理廠更換新的剎車燈。
If there is no spare light bulb, the owner must slow down carefully. On the one hand, turn on the danger alarm lamp, on the other hand, decelerate on the right, looking for the nearest repair shop to replace the new brake lamp.
在這里我想提醒業主的檢查和維護剎車燈泡必須分為常規檢查項目,特別是在所有傷害的情況下剎車燈泡,風險很大,一旦發現剎車燈泡損壞必須更換盡快為了及時隱患。
Here I would like to remind the owners that the inspection and maintenance of brake light bulbs must be divided into routine inspection items, especially in all cases of injury, the safety risk is very high, once the brake light bulb damage is found, it must be replaced as soon as possible in order to eliminate the potential safety hazards in time.